SCV31 unlock done but still lock

Home  >>  Z3X box Section  >>  SCV31 unlock done but still lock

SCV31 unlock done but still lock

On January 28, 2018, Posted by , In Z3X box Section, With 2 Comments


UNLOCK INSTRUCTIONS:
1. Power on the phone.
2. Type *#0808# and select DM+MODEM+ADB.
3. Type *#9090# and select DM/DUN over HSIC.
Or use Activate Diag function from Repair tab.
4. Connect the phone to PC Along with USB cable, install drivers if wanted.
5. Select diagnostic port in port settings.
6. Press Unlock button for direct unlock.

Operation: Unlock
Selected model: SCV31
Selected port: COM683 SAMSUNG Mobile USB Serial Port
Software version: 30.4

Reading phone info…
Reading IMEI… OK
IMEI: 354207070241305
Unlocking… OK
Reseting… OK
Unlock done

Done Along with Samsung Tool PRO v.30.4

2 Comments so far:

  1. Bo-Rens says:

    not work this method

  2. wagny says:
    Quote:
    rn babumnmm
    UNLOCK INSTRUCTIONS:
    rn 1. Power on the phone.
    rn 2. Type *#0808# and select ‘DM+MODEM+ADB’.
    rn 3. Type *#9090# and select ‘DM/DUN over HSIC’.
    rn Or use ‘Activate Diag’ function from ‘Repair’ tab.
    rn 4. Connect the phone to PC Along with USB cable, install drivers if wanted.
    rn 5. Select diagnostic port in port settings.
    rn 6. Press ‘Unlock’ button for direct unlock.

    rnOperation: Unlock
    rnSelected model: SCV31
    rnSelected port: COM683 SAMSUNG Mobile USB Serial Port
    rnSoftware version: 30.4

    rnReading phone info…
    rnReading IMEI… OK
    rnIMEI: 354207070241305
    rnUnlocking… OK
    rnReseting… OK
    rnUnlock done

    rnDone Along with Samsung Tool PRO v.30.4

    First, of course, you want this great box, Z3X. Then you want SPT box to write super IMEI.

    rnFiles you want, thanks to vietmobile.vn for sharing:
    https://drive.google.com/file/d/0B7M…w?pref=2&pli=1
    rnPassword:fullscv31

    rnBEFORE DOING ANYTHING, WRITE DOWN THE ORIGINAL IMEI # somewhere. Make sure you know the original IMEI

    rn1). Flash Combination file using Odin. After flashing, phone will be in Factory Binary Mode. Tab one Android logos at the bottom of the screen to get to dial pad and enter *#0808# and select DM+MTP+ADB then OK.

    rn2). Use Z3X, select the SCV31 model and go to Repair tab and press on Reset MSL.

    rn3). Write down the phone’s original IMEI# somewhere and save it. Use SPT box and go to Service tab and in Repair IMEI, enter this super IMEI : 358012060753038 (this is an original factory unlocked IMEI) Use C3300 UART cable and write new IMEI to phone. After it finished, check to make sure you have the new IMEI in phone.

    rn4). Flash FULL flash files (BL, AP, CP, CSC) and no want PIT file, using Odin.

    rn5). After flashing full flash files, inset any SIM card, phone boots up and go to WIFI and turn on. Go to Settings>>About>>SIM card status. You should see Status: Not allowed. Tab on "Update SIM card status" at the bottom of the screen then wait until it finished and reboot. Go back to SIM card Status again and see if it shows Status: Allowed. If it is, then you’re good to go to the next steps.

    rn6). Repeat Step 1,2, and 3, except in Step 3, enter phone’s ORIGINAL IMEI. After all steps done, check to make sure you have original IMEI in phone now.

    rn7). Now flash FULL flash files (BL,AP,CP,CSC) again. After flashing is done, phone should be now UNLOCKED.

    rnIf you want to remove AU Japanese contents in ROM, you can flash this SPACX ROM using Odin: